Stixall everbuild

Stixall

Ultimate combined building adhesive and sealant

Stixall

  • Ultimate combined building adhesive and sealant
  • Based on hybrid polymer technology
  • Extreme power to bond virtually EVERYTHING to ANYTHING in virtually all conditions, even under water or in the rain!


STIXALL is a one part, chemically curing solvent free sealant and adhesive combining the best qualities of silicone and polyurethane technologies. It is specifically designed for adhering most common building surfaces to each other and themselves.


Code Product Boxed In
080005 Stixall White 1
080007 Stixall Clear 1

Technical Data
 

ConsistencyPasty
Density1.50 ± 0.05
Application Temperature5 to 35°C
Skin Formation at 23°C
and 50% RH
30 ± 10 mins
Sagging (ISO 7390)Nil
Curing at 23°C and 50% RH> 3mm / 24hr
Shore A Hardness (ISO 868 – 3 seconds)55 - 60
Modulus at 100% Elongation (ISO 8339)> 1 MPa
Elongation @ Break (ISO 8339)> 100%
Tensile Strength (ISO 8339)> 1.5 Mpa
Shrinkage (ISO 10563)< 2%
Resistance To UV RadiationExcellent
Compatibility With PaintsWater based: yes (test compatibility)
Solvent based: no (with alkyd paints)
Temperature Resistance-40 to +150°C
Movement Accommodation± 20%
CoverageApproximately 11 linear meters per cartridge

Application

Cut the tip of the cartridge taking care not to damage the thread. Fix nozzle, cut aperture to required width and apply with a standard sealant gun.
As a nail replacement (panel) adhesive.
  • Surfaces must be sound, clean, dry and free from dust, grease, loose material etc.
  • Prime dusty surfaces with EVERBUILD PVA BOND diluted 1:4 with water and allow to dry.
  • Apply using a standard sealant gun, cut tip of cartridge, apply nozzle and cut an opening to suite the required bead
    size.
  • For bonding heavy items (Plasterboard/worktops/wall panels etc) apply adhesive all the way around the edge of the
    item (30-50mm from edge) and cover back with beads of adhesive at 300mm intervals. Alternatively, apply adhesive
    direct to battens and press into place. NOTE.
  • With heavy items, always provide temporary support until the adhesive dries.
  • For bonding lightweight items (covings, dado rails, skirting etc) apply adhesive to back of item in one or two continuous beads and press immediately into place.
  • Where gap filling is required, mark the areas where there is a large gap and apply a thicker bead to these areas.
    In all cases, clean up excess adhesive immediately with a cloth/white spirits.

As a sealant

Reference should be made to the recommended joint ratios. If necessary reduce joint depth using Everflex Expanding Foam, or Joint backer rod. Furthermore, ensure that the joint design only permits adhesion to two surfaces, as three sided adhesion will impair flexibility.
Where the sealant is used in a joint configuration, masking tape should be used to prevent contamination of adjacent substrates, and ensure a neat sealing line. Masking tape should be removed immediately after tooling. The joint should be tooled within 5 minutes of application to ensure good contact between the sealant and the substrate. Tooling of the sealant also gives a smooth, professional finish.

Fixing mirrors

Apply 6mm diameter beads of sealant direct to back of mirror in vertical strips, spaced at 30-40mm centers. Immediately place mirror in position and secure with good, even pressure with a slight twist action. Provide temporary support (tape) until adhesive has dried (24-48 hours). If required, STIX-ALL may also be used to seal around mirror 24 hours after fixing (to allow for cure)

Uncured material can be removed by wiping with a dampened cloth with white spirit. Cured material can be carefully removed by mechanical means. Full cure must be allowed before over painting.
 
Storage

Store in original unopened containers between 5'C and 25'C. Shelf live of 12 months in original unopened containers
File Download
Stixall Extreme Power rev 11 .doc
Everbuild Stixall Extreme Power SDS v0.pdf